1) Adjust the observation mirror to be parallel to the guide rail. The value changes counterclockwise to negative and clockwise to positive. The green cross line above the baseline indicates a high point. The green cross below the baseline indicates a low point.

　　2)、導軌分段，導軌上面有螺栓孔，兩個螺栓孔之間為一段，這樣導軌就分成幾段。把反光鏡移動到非常靠近光管的那一段上面，調整綠十字線和基線重合，刻度調成0.把這個段作為基準段。

2) The guide rail is divided into several sections, with bolt holes on top of the guide rail and a section between the two bolt holes. Move the reflector to the section closest to the light tube, adjust the green cross line to coincide with the baseline, and adjust the scale to 0. Use this section as the reference section.

　　3)、反光鏡移動到下一段，調整綠十字線和基線重合，看刻度，把數值記錄下來，依次到非常后一段。

3) Move the reflector to the next section, adjust the green cross line to coincide with the baseline, observe the scale, record the values, and proceed to the last section.

　　4)、開始調整導軌的螺栓，原則是那個點高就緊螺栓，低則松螺栓。5)、重復以上的調試過程，直到調到公差范圍即可(0.003mm)。

20181206042250134

4) Start adjusting the bolts of the guide rail. The principle is to tighten the bolts at the high point and loosen the bolts at the low point. 5) Repeat the above debugging process until the tolerance range is reached (0.003mm).

　　6)、如果無法調整到公差范圍，那個點高，那段位置的基面需要重新刮研。然后再進行調整，直到完成。

6) If it is not possible to adjust to the tolerance range, the base surface at that point needs to be re scraped. Then make adjustments until completed.

　　六、校正直線度。

6、 Correct straightness.

　　1)、把觀察鏡調成與導軌垂直。數值變化為逆時針為正，順時針為負。綠色十字線在基線的右側說明這點高。綠十字線在基線的左側說明這點低。

1) Adjust the observation mirror to be perpendicular to the guide rail. The value changes counterclockwise to positive and clockwise to negative. The green cross line on the right side of the baseline indicates a high point. The green cross on the left side of the baseline indicates a low point.

　　2)、把導軌壓塊放入槽中，稍微擰緊即可(力度不能過大)。

2) Place the guide rail pressure block into the slot and tighten it slightly (the force should not be too strong).

　　3)、兩個壓塊之間為一段，這樣把導軌分成若干段。把反光鏡移動到非常靠近光管的那一段上面，調整綠十字線和基線重合，刻度調成0.把這個段作為基準段。

3) The guide rail is divided into several sections by forming a section between two pressure blocks. Move the reflector to the section closest to the light tube, adjust the green cross line to coincide with the baseline, and adjust the scale to 0. Use this section as the reference section.

　　4)、反光鏡移動到下一段，調整綠十字線和基線重合，看刻度，把數值記錄下來，依次到非常后一段。

4) Move the reflector to the next section, adjust the green cross line to coincide with the baseline, observe the scale, record the values, and proceed to the last section.

　　5)、開始調整壓塊的螺栓，原則是那個點高就緊螺栓，送則松螺栓。6)、重復以上的調試過程，直到調到公差范圍即可(0.003mm)。

5) Start adjusting the bolts of the pressure block. The principle is to tighten the bolts at that point and loosen them when sending. 6) Repeat the above debugging process until the tolerance range is reached (0.003mm).

本文由導軌絲杠友情奉獻，更多有關的知識請點擊:http://www.traderpanda.net/真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is dedicated to the friendship of guide rail screws. For more related knowledge, please click on. jiangongrun.com Sincere attitude. We will provide you with excellent service. We will continue to contribute more related knowledge to you. Stay tuned